Recent Posts

Pages: 1 2 [3] 4 5 ... 10
21
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on August 17, 2020, 01:00:45 PM »
Yes you right, a lot better than a bit of fibreglass bonded to a kitchen door hinge.
22
Build Threads / Re: DADS360 - THE Build diary!
« Last post by AIG1355 on August 15, 2020, 10:37:32 AM »
Looks like you're pretty safe in the thought that its not going to snap off in your hand at the most inopportune moment.
23
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on August 14, 2020, 07:57:01 PM »
Been busy looking after my grandson ,it's school holidays .Mrs Chevy and I took him yesterday to East Kirby to see "Just Jane" this is an up and running world war two Avro Lancaster. The roar of four Rolls Royce Merlin V 12 engines screaming at full chat literally takes you breath away .The smell of 100 + octane avgas is enough to make you go funny.
In the time I had on the project I made the bracket that hold the outer door handle to the door skin. Next is to make the two brackets that secure the inner door cable.
24
Extreme Murcie / Re: There’s a replica engine on ebay
« Last post by mikemurci on August 08, 2020, 09:24:02 PM »
Anyone know where I can find one like this ??
25
Build Threads / Re: Lloydmeister Build Pics
« Last post by dads360 on August 07, 2020, 07:45:49 PM »
Hi, can you remember where you go the wheels from ?.
26
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on August 07, 2020, 07:40:26 PM »
Back on the passenger door, reinforcement  plates made, these will be welded and bolted in place. Shot of the inner door modified and ready to go.
27
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on August 03, 2020, 12:18:24 PM »
I have been busy with family MOT's so progress has been slow on the passenger door. But I did have chance to sort out the steering wheel.
28
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on July 10, 2020, 04:27:58 PM »
Door mechanism now fitted in the nearside door. photo's show the misalignment of the back edge of the drop glass to the rear quarter panel. This is fixed by putting in a new B post. This corrects the misalignment and also becomes hidden under the rear Ferrari quarter light glass. The roof rails are next to be modded and then to work on the outside handle and stiffen up the back of the door behind the fibreglass door cap.
29
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on July 03, 2020, 05:13:44 PM »
Sorry for the poor photos in the previous post. I have now completed the refabricating of the Audi A3 door window mechanism for the passenger side. Shown are the handed pair of mechanisms. The door bar is fitted to the door, so now it's time for all the hard work of fitting the frame into the door shell and doing the internal linkage and outer door handle. Just out of interest it was me who identified the Audi A3 two door as a candidate for the Extreme 360 kit .During my day job I drove around the country visiting customers and dealerships, so took the plastic window that came with the kit and used to walk around the company car parks offering up the window to see if any were suitable. When I had identified the Audi as suitable I shared the info with the team at Extreme. The engine support frame is back from powder coating. It's coming along now, next is repositioning the B post and then the steel roof.
30
Build Threads / Re: DADS360 - THE Build diary!
« Last post by dads360 on June 28, 2020, 01:43:47 PM »
Made a start on the nearside door, hockey stick and end cap sorted. Collision bar removed from inside the door and prepped ready to bolt and glue to the outside of the door.
Pages: 1 2 [3] 4 5 ... 10

Advert